Did anyone have Enduraflood installed & then have surge waters rush through their home? (Rather than slowly rise inside.) If so, did the panels stay on the wall?

Hi, Can anyone tell me the difference btn base flip and base clip? What is spacer used for? Thank you,

What type of paint (latex? water-based?) are folks using and how has it held up post-flood? One person told me I should use latex paint only, but that doesn't seem to be what is recommended in the Design Inspirations by Enduraflood. Anyone experience how their painted Enduraflood panels/trim held

Has anyone caulked below or above the baseboards and then used a knife to slice caulk before removing during a flood? Trying to get the tightest fit for insect deterrence and insulation purposes. Thank you!

I don't see anything on the website that Enduraflood panels will be unharmed after sitting his hours of saltwater, sandy storm surge. Has this been tested or does the company not make that claim for fear of it failing?

For our house in Florida we have furring strips on concrete walls. They are about 3/4" deep. Can we mount EnduraFlood there too?

Is there a trim piece used where the stud wall/endu-board abuts a concrete bock wall at an inside corner? What about at a door frame?

I plan to buy the panels for my home in Maine. Do the panels come in different colors? Also, does anyone know how long they take to get to Maine?

Is Endu-Koard any more durable than Endu-Board?

Any tips for measuring & making holes into the ENDU-BOARD for outlets or wires of baseboard heaters? I didn't see this in the tips videos (and am located in Montreal, Canada, so I'm not sure if there are any affiliated contractors in the area, so am planning to do they install myself).

Has anybody done an installation in a home with the round corners? We have round edges around 3 sets of glass sliders and one other “frame” that is rounded. Wondering what solution there is for those types of corners. We’re still making decisions on the product as we rebuild after Helene flooded u

Our room where we want to use the Enduraflood system has walls with different thickness of drywall, either 1/2" or 5/8". Is there a solution to handle corners where the different sizes meet?

Is there a recommended practice to simply the reassembly of the panels, corners and trim following a flooding event? Without that, wouldn't pieces get confused and become a mess trying to put everything back to where it was? Thanks in advance for your prompt response! We are installing as we sp

Does anyone have any advice for cutting the drywall when floor is uneven. Wondering if we need to adjust how we install

Does anyone know of the fire rating of EnduraFlood.? I need to know if it complies with the building codes. Thank you!

Do most people paint the boards or can we leave them as is? I now understand that they come in white but do they HAVE to be painted? We are using some sections in a storage type room, like a mud room. And based on the sample kit I think we could just leave the boards as is. Does anyone have any expe

As I'm planning my order, my wife would like us to go with the traditional chair rail trim. But when I start to "build my order" (24" height), it does not allow me to include traditional chair rail for that height and 1/2" drywall width. Is there a reason for this? It seems like RAILI-HOLD/12 and CH

We have leftover baseboards from another project. Can you use regular baseboards rather than the ones sold here?

What is the time to shipment for an order of 200 lin feet? Can't find this information anywhere, thanks in advance everyone!

Just wondering if anyone has had experience with having to remove the panels after they were installed? Was it easy to do and easy to place back?

We completed our demo from Helene at 49”, do we need to open this up to 51 inches to use the endurance flood or can we go with the 49 which is completed.

I am working on my order- I called Customer service and since it is Sat, I am assuming I will not hear back until Monday, so thought I would post here. I am ordering 2 different panel types for different rooms (EnduBoard and EnduKoard) and do not want to pay shipping on 2 separate orders. I think

any data on how this affects home value?

I am rebuilding the ground floor walls in my Florida stilt house and this looks like the right material to finish the walls. I am planning to waterproof the wood with Red Guard or a similar material and I was planning to insulate it with closed cell polyurethane spray foam that does not absorb wate

Just made my 52" Harrington order a few days ago and have a painting question. Most of the photos I've seen using Harrington leave the vertical strips between panels white. I think leaving the vertical strips white makes the wall a little busy and broken up versus a solid color. Is there a probl

Asking all contractors: What are your thoughts on the Owens Corning basement system. We have been asked by a few customers about use in their basement. I have mixed emotions about it. The panels go to the ceiling so you have access to the pipes etc. But what are your thoughts about effectiveness in

For my floodprone basement I am looking at the Greenwood and Albright suites. On the photos it looks like there is a difference between the width of the slats that go up and down. Does anyone have the specs? I have looking through the product descriptions but have not been able to find the answer. T

Just came across this system and it seems like it could be a very good solution for our basement. Wondering if there are any distributors or stores in Ohio (Portage County) where I could see the product. Thank you

At a few places in our basement, we have two immediately adjacent corners (almost like a "Z"), of an inside then then outside corner, with only a couple inches along a short wall. Or around the edges of our closets (sliding doors) where it would be two outer corners right next to each other. What w