Community Chat

I am looking at using Enduaflood to address the area in my garage that used to have drywall before the flooding we suffered last year as a result of hurricane Helene. I am trying to understand if it would be possible to do a custom installation of the boards on the underside of the staircase that l

Hello everyone, for some reason it looks like a previous thread about this same topic is not available so I cannot add this to that one. I did want to drop a follow-up note so others wouldn't go through what I did. I tried two different staplers and three different brands of staples trying to fin

When intalling the verticore - O pieces, there is really nothing holding the top of the corner piece to the Endu-board... Has anyone noticed this? Am I installing these outside corners incorrectly? Should I use, say, some silicone or other caulk at the top to hold the corner trim piece in place?

We are doing a home where the wall are not 16" oc and we having to install 2x4 studs or 2x1/4 strips so the ends of the panels have a solid support to fit on. Is anyone have this problems? How are you handling the panels not hitting a stud?

How is the product shipped? Is it packaged in boxes that say what's inside? Is it shipped so its visible? Is it shipped in plain cartons? The reason I ask is our local code enforcement is prowling the area requiring permits for such minor things and baseboard replacements et al. and I'm not re

Do I need a vapor barrier with Endura Flood panels?

Has anybody done an installation in a home with the round corners? We have round edges around 3 sets of glass sliders and one other “frame” that is rounded. Wondering what solution there is for those types of corners. We’re still making decisions on the product as we rebuild after Helene flooded u

Our room where we want to use the Enduraflood system has walls with different thickness of drywall, either 1/2" or 5/8". Is there a solution to handle corners where the different sizes meet?

In the estimator there was a question about the number of doors. I put in 8 doors because we have quite a few, but I am not sure what the meaning of this question was. I just went along. Before I get my order can someone advise what the meaning of this question was? Thank you in advance!

I would label the panel in this order from Left to Right in each room. To Put back the assembly after a flood, Install Vertical, then panel, then vertical, panel, Finally Base 1,2,3,4..... (1) Room Id, (2)Vertical Trim label as A,B,C... (3) Panel ID..1,2,3,4... Wall Base ID..1,2,3,4,,. "Bedrm, A

Working for a customer fixing hurricane damage and this is first time installing product. Looking for some advice on how to navigate this situation. The height for cut was right in line with where railing attaches. The panels dont appear to work next to stairs because I can’t get behind to install

Replacing whole 8’ tall walls. Does it matter if the upper wallboard is replaced first or is it better to have the enduroflood installed first

Has anyone installed panels up a stairwell? I had 4 1/2 ‘ of water for Helene and would like to install panels on the bottom half of my stairwell. Any photos appreciated

I live on the Gulf in FL in an AE zone. My first floor is concrete block with flood vents. I would like to use Enduraflood for interior walls and butt the panels against the block walls, then paint the block walls. Should I use a corner piece at the end against the block walls to create a finished

Should I seal the exposed cut of the drywall before installing the Raili gold trim, If so what product should I use?

Did anyone have Enduraflood installed & then have surge waters rush through their home? (Rather than slowly rise inside.) If so, did the panels stay on the wall?

We completed our demo from Helene at 49”, do we need to open this up to 51 inches to use the endurance flood or can we go with the 49 which is completed.

My home has plaster walls. Plaster walls have a thickness of around 7/8". What would be the solution to install Enduraflood panels? 1/4" Shims are an option for the ENDU-BOARD (to connect to 5/8" drywall) but maybe people have other ideas. I'd also love to use ENDU-KOARD in at least one room (whic

I received this from Enduraflood support the other day since I could not figure out how to count the inside corner vs the outside corners. They also said to count inside corners in a closet the same as any other inside corner. I thought this may help someone!

The project builder put both in my cart. Seems to me I need one or the other , not both.

Has anyone installed the routered panels sideways so the lines run horizontally?

Hi, I live on the Gulf Coast of Florida and was wondering what insulation to use behind EnduraFlood, I want something that won’t absorb water and still be fire resistant, I was going to use closed cell ridged foam boards with a 15 minute thermal barrier so I can just take it out clean and dry it aft

Given the vertical pattern two Qs: 33” is the height from floor? Please confirm. What would be the drywall cut from floor in inches?

When removing is it necessary to remove the wainscoting trim? ALSO,, has anyone come up with a method for numbering? It ilooks as if I will need to number panels, & baseboards!!!! Maybe some verticals? Maybe wainscoting trim IF IT NEEDS REMOVED.....

Good morning. Has anyone ever installed the Endura Flood panel on a curved wall?

Hi, Can anyone tell me the difference btn base flip and base clip? What is spacer used for? Thank you,

I am working on my order- I called Customer service and since it is Sat, I am assuming I will not hear back until Monday, so thought I would post here. I am ordering 2 different panel types for different rooms (EnduBoard and EnduKoard) and do not want to pay shipping on 2 separate orders. I think

What type of paint (latex? water-based?) are folks using and how has it held up post-flood? One person told me I should use latex paint only, but that doesn't seem to be what is recommended in the Design Inspirations by Enduraflood. Anyone experience how their painted Enduraflood panels/trim held